Siemens SCALANCE XR-300M PoE Series Compact Operating Instructions Download Page 67

Page: 67 / 92

Technical specifications

Note
Validity of the technical specifications

All the technical specifications described in this section that is not assigned to a specific device
variant, version or a media module, apply to all device variants/versions of the product group.

8.1

Construction, installation and environmental conditions

Table 8-1

Construction

Dimensions (W x H x D)

449 × 43.6 × 305 mm

Weight

6800 g

Degree of protection

IP20 (with closed service panel)

Table 8-2

Installation options

Device version
(power supply)

Installation options

24 VDC

• 19" rack
• Desktop operation with adhesive feet

100 to 240 VAC

19" rack

Table 8-3

Permitted ambient conditions

Storage/transport temperature

-40 °C to +85 ℃

Max. relative humidity in operation at 25 °C

<= 95% (no condensation)

Max. ambient temperature at operating altitude

2000 m or above:
-5 °C of the max. operating temperature

3000 m or above:
-10 °C of the max. operating temperature

See table: "Operating temperature depending on the media modules used"

SCALANCE XR-300M PoE
Compact Operating Instructions, 03/2022, A5E02661178-15

Summary of Contents for SCALANCE XR-300M PoE Series





























































































Search results

Summary of Contents for SCALANCE XR-300M PoE Series

Reviews:

Related manuals for SCALANCE XR-300M PoE Series

Brands by name

Popular brands

Siemens SCALANCE XR-300M PoE Series, Compact Operating Instructions

Search results

Summary of Contents for SCALANCE XR-300M PoE Series

Reviews:

Related manuals for SCALANCE XR-300M PoE Series

Brands by name

Popular brands