manualshive.com logo in svg

Siemens SCALANCE XR-300M PoE Series, Compact Operating Instructions

Share
Download
Siemens SCALANCE XR-300M PoE Series Compact Operating Instructions Download Page 59

Safety notices when using the device according to Hazardous Locations (HazLoc)
If you use the device under HazLoc conditions you must also keep to the following safety notices 
in addition to the general safety notices for protection against explosion:

WARNING

EXPLOSION HAZARD

You may only connect or disconnect cables carrying electricity when the power supply is 
switched off or when the device is in an area without inflammable gas concentrations.

6.7.1.1

Overview

Table 6-2

24 V DC safety extra low voltage

Device

Device version (power supply)

24 V safety extra-low voltage 

(SELV)

can be connected redundantly

XR324-4M PoE

1 x 24 V DC

●

XR324-4M PoE TS

1 x 24 V DC

●

See also

Connecting devices with 100 to 240 VAC power supply (Page 61)

Connecting up

6.7 Power supply

SCALANCE XR-300M PoE
Compact Operating Instructions, 03/2022, A5E02661178-15

59

Summary of Contents for SCALANCE XR-300M PoE Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands