manualshive.com logo in svg

Siemens SCALANCE XR-300M PoE Series, Compact Operating Instructions

Share
Download
Siemens SCALANCE XR-300M PoE Series Compact Operating Instructions Download Page 61

Terminal block assignment (4-pin)

Table 6-3

Pinout of the 24 V safety extra-low voltage (SELV)

Pin number

Assignment

Labeling (example)

Pin 1

L1+ (24 VDC)

Pin 2

M1

Pin 3

M2

Pin 4

L2+ (24 VDC)

To wire up the power connector, use a copper cable of category 20-12 AWG or cable with a cross-
section of 1.0 to 2.5 mm².

6.7.2

Connecting devices with 100 to 240 VAC power supply

Safety note on devices with 100 to 240 V AC power supply

WARNING

Danger from line voltage

The supply voltage for the devices listed is 100 to 240 V AC.

This device can only function correctly and safely if it is transported, stored, set up, and installed 
correctly, and operated and maintained as recommended.

Connecting and disconnecting may only be performed by an electrical specialist.

Connect or disconnect power supply cables only when the power is turned off.

WARNING

Devices with a 100 to 240 V AC power supply do not have an ATEX or IECEx approval.

Devices with a 100 to 240 V AC power supply are not approved for use in hazardous areas 
according to 2014/34/EU ATEX or IECEx.

Connecting up

6.7 Power supply

SCALANCE XR-300M PoE
Compact Operating Instructions, 03/2022, A5E02661178-15

61

Summary of Contents for SCALANCE XR-300M PoE Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands