Siemens SCALANCE X101-1 Commissioning Manual Download Page 30

Page: 30 / 86

Product Characteristics

4.3 SCALANCE X101-1FL

4.3.4

SCALANCE X101-1FL TP Port

Connector Pinout

RJ-45 jack

Figure

4-8

RJ-45 connector pinout

Pin number Pinout

Pin 8

Pin 7

Pin 6

TD-

Pin 5

Pin 4

Pin 3

TD+

Pin 2

RD-

Pin 1

RD+

On SCALANCE X101-1FL, the twisted pair port is implemented as RJ-45 jack with MDI-X

assignment (Medium Dependent Interface

–

Autocrossover) of a network component.

Notice

TP cords or TP-XP cords with a maximum length of 10

m can be connected to the RJ-45 TP

port.

Depending on the cable type, a total cable length of up to 100 m is permitted between two

devices with the IE FC cables and IE FC RJ-45 plug 180.

Note

The SCALANCE X101-1FL works with a fixed transmission speed of 10 Mbps in half duplex.

Devices not supporting autonegotiation must be set to 10 Mbps half duplex.

Industrial Ethernet Media Converters SCALANCE X-100 Series

4-16

Commissioning Manual, 07/2008, A2B00051521A

Summary of Contents for SCALANCE X101-1























































































Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands

Siemens SCALANCE X101-1, Commissioning Manual

Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands