Siemens SCALANCE X101-1 Commissioning Manual Download Page 11

Page: 11 / 86

Network Topologies

3.1

Network Topologies

Which network topologies can be implemented?

With an Industrial Ethernet media converter of the SCALANCE X-100 series, bus and star

topologies can be implemented. In addition, it is possible to couple

rings and the usage of

two identical media converters

in a ring network. Please compare in chapter 4 Product

Characteristics, subsection Cascade, of the concerning media converter.

Bus Topology

Figure

3-1

Electrical/optical bus topology with SCALANCE X101-1

Only SCALANCE X101-1 or SCALANCE X101-1LD or SCALANCE X101-1POF

Industrial Ethernet Media Converters SCALANCE X-100 Series
Commissioning Manual, 07/2008, A2B00051521A

3-1

Summary of Contents for SCALANCE X101-1























































































Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands

Siemens SCALANCE X101-1, Commissioning Manual

Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands