Siemens SCALANCE W788C-2 Operating Instructions Manual Download Page 11

Page: 11 / 50

SCALANCE W788C-2
Operating Instructions, 07/2019, A5E03692120-14

Description

3.1

Description of the device

SCALANCE W7x8x-x RJ45 - IP30 degree of protection

①

LEDs

②

Connecting connectors, R-SMA type female

•

Devices with one IWLAN interface: 3 connectors on the top (covered in the figure).

•

Devices with two IWLAN interfaces: 3 connectors on the top and 3 on the underside.

③

Connector for power supply

④

Connector for Ethernet, RJ-45 type

⑤

Screw-down cover for the

- reset button and the

- PLUG compartment (not with W788C)

⑥

Connector for the digital input/output (not with W788C)

⑦

PLUG compartment (not with W788C)

⑧

Reset button

⑨

Grounding connector (thread M4) on the back of the device

Figure 3-1

SCALANCE W7x8 RJ45

Summary of Contents for SCALANCE W788C-2



















































Search results

Summary of Contents for SCALANCE W788C-2

Reviews:

Related manuals for SCALANCE W788C-2

Brands by name

Popular brands

Siemens SCALANCE W788C-2, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE W788C-2

Reviews:

Related manuals for SCALANCE W788C-2

Brands by name

Popular brands