manualshive.com logo in svg

Siemens S55561-F112, Manual, Page: 2 / 40

Share
Download
Siemens S55561-F112 Manual Download Page 2

2 / 40 

Siemens 

Ultrasonic heat and cooling energy meters UH50.. 

CE2N5324en 

Building Technologies 

 

2013-01-14 

Application 

The UH50.. heat and cooling energy meter acquires energy consumption in a 
physically correct way. The device consists of flow measuring section and proces-
sor unit. The processor unit can be equipped with different sensors, different types 
of power supply and communication modules. The UH50.. is used to measure the 
consumption of heat in district heating systems and blocks of flats. It is also suited 
to measure the consumption of cooling energy (cooling energy only or in combina-
tion with thermal energy), or volume flow in hydronic systems. 

The UH50.. must not be used in connection with drinking water. 
Also, the product is not suited for use in systems operating on water-glycol mix-
tures. 
 

Functions 

The volume flow is acquired based on the ultrasonic measuring principle, free from 
wear, thanks to the use of non-moving parts. 

The quantity of energy supplied to the consumer by the medium during a certain 
period of time is proportional to the temperature differential of flow and return and 
the volume flow passing through the meter.  

The 

water volume

 is measured in the measuring tube by ultrasonic pulses which 

are transmitted in the direction of flow and against the direction of flow. Down-
stream, the time required by the pulses to travel from the transmitter to the receiver 
is reduced, upstream it is increased. The water volume is then calculated based on 
the values measured for the traveling times. 

The

 flow and return temperatures

 are determined using platinum resistors. 

The heating water volume and the temperature differential of flow and return are 
multiplied and its product integrated. The result, which is the consumed 

quantity of 

thermal or cooling energy

, is registered and displayed in the physical 

units

 

kWh/MWh or MJ/GJ, 

the volume in 

m

3

. 

 

A standard electronic unit is used for all flow rates with identical operation and an 
integrated service unit. 

The meter is equipped with an optical communication interface, enabling the de-
vice to be read and parameterized on site with the help of the WZR-OP-USB opti-
cal read head and the UltraAssist software. 

The meter performs constantly self-diagnostics, allowing it to detect a number of 
mounting or device errors and to display them. 
 

Type summary UH50.. 

The types of meters listed below are equipped as follows: 

Mounting location 

Return 

Rated pressure 

PN 16/PN 25 

Length of control cable 

1.5 m/3 m 

Sensor mounting 

Return temperature sensor, integrated in the  

 

flow measuring section 

 

Return temperature sensor, not integrated in  

 

the flow measuring section 

Restrictions 

Ultrasonic measuring 
principle 

Processor unit 

Optical communication 
interface 

Self-diagnostics 

Summary of Contents for S55561-F112









































Reviews:

No comments