Siemens RWF40 Series User Manual Download Page 33

Page: 33 / 56

Landis & Staefa Division

CC1B7865E

February 10, 2000

33/56

6. Operation

✱

Press

EXIT

for 5 s

The LED above the hand symbol lights up.

✱

Change the regulating unit’s position with

▲

and

▼

Relay 2 opens the regulating unit as long as

▲

is pressed.

Relay 3 closes the regulating unit as long as

▼

is pressed.

The LEDs for the regulating units indicate if «OPEN» or «CLOSE» is activated.

✱

Change the regulating unit’s position with

▲

and

▼

The modulating output delivers the regulating unit’s position that was entered.

✱

Return to automatic operation by pressing

EXIT

for 5 s

)

When manual operation is activated, the regulating unit’s position is set to 0
until another entry with the buttons is made.

Manual operation can only be activated if the thermostat function has set relay 1 to

active

If the thermostat function sets relay 1 to

inactive

during manual operation, manual

operation is terminated.

✱

Press

EXIT

for 5 s

✱

Press

▲

briefly

−

Relay 2 is active, relay 3 is inactive

−

Analog output (optional) delivers DC 10 V

The regulating unit opens

✱

Or press

▼

briefly

−

Relay 2 is inactive, relay 3 is active

−

Analog output (optional) delivers DC 0 V

The regulating unit closes

✱

Return to automatic operation by pressing

EXIT

for 5 s

)

If the thermostat function sets relay 1 to

inactive

during manual operation,

manual operation is terminated.

6.2.2 Manual operation, modulating burner

3-position controller

Modulating controller

Thermostat mode

6.2.3 Manual operation, two-stage burner

Summary of Contents for RWF40 Series

























































Search results

Summary of Contents for RWF40 Series

Reviews:

Related manuals for RWF40 Series

Brands by name

Popular brands

Siemens RWF40 Series, User Manual

Search results

Summary of Contents for RWF40 Series

Reviews:

Related manuals for RWF40 Series

Brands by name

Popular brands