Siemens RUGGEDCOM RX1512 Installation Manual Download

Page: 43 / 52

Technical Specifications
5.4 Mechanical Specifications

Ambient Relative Humidity

5% to 95%

Maximum Altitude

2000 m (6562 ft)

Maximum ambient operating temperature is 70 °C (158 °F) when the device is installed along with

Underwriter Laboratories (UL) listed devices.

Measured from a 30 cm (12 in) radius surrounding the center of the enclosure.

Operating temperature may vary based on the limitations of installed SFPs. Refer to the

RUGGEDCOM

SFP Transceivers Catalog

for SFP temperature ratings.

Non-condensing.

5.4

Mechanical Specifications

Weight

Approximately 2.3 kg (5 lb)

Ingress Protection

IP30

Enclosure

Aluminum

5.5

Dimension Drawings

Note

All dimensions are in millimeters, unless otherwise stated.

122.7

184.4

Figure 5.1

Overall Dimensions

RUGGEDCOM RX1512

Installation Manual, 07/2019, C79000-G8976-1057

Summary of Contents for RUGGEDCOM RX1512





















































Search results

Summary of Contents for RUGGEDCOM RX1512

Reviews:

Related manuals for RUGGEDCOM RX1512

Brands by name

Popular brands

Siemens RUGGEDCOM RX1512, Installation Manual

Search results

Summary of Contents for RUGGEDCOM RX1512

Reviews:

Related manuals for RUGGEDCOM RX1512

Brands by name

Popular brands