manualshive.com logo in svg

Siemens RUGGEDCOM RS900F, Installation Manual

Share
Download
Siemens RUGGEDCOM RS900F Installation Manual Download Page 41

RUGGEDCOM RS900F

Installation Guide

Chapter 6

Certification

Approvals

31

Certification

The RUGGEDCOM RS900F device has been thoroughly tested to guarantee its conformance with recognized

standards and has received approval from recognized regulatory agencies.

CONTENTS

•

Section 6.1, “Approvals”

•

Section 6.2, “EMC and Environmental Type Tests”

Section 6.1

Approvals

This section details the standards to which the RUGGEDCOM RS900F complies.

CONTENTS

•

Section 6.1.1, “CSA”

•

Section 6.1.2, “CSA/Sira”

•

Section 6.1.3, “European Union (EU)”

•

Section 6.1.4, “FCC”

•

Section 6.1.5, “FDA/CDRH”

•

Section 6.1.6, “ISED”

•

Section 6.1.7, “TÜV SÜD”

•

Section 6.1.8, “RoHS”

•

Section 6.1.9, “Other Approvals”

Section 6.1.1

CSA

This device meets the requirements of the following Canadian Standards Association (CSA) standards under

certificate 16.70065161:
•

CAN/CSA-C22.2 No. 60950-1

Information Technology Equipment – Safety – Part 1: General Requirements (Bi-National Standard, with UL

60950-1)

•

UL 60950-1

Information Technology Equipment – Safety Part 1: General Requirements

Summary of Contents for RUGGEDCOM RS900F

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands