manualshive.com logo in svg

Siemens RUGGEDCOM RS900F, Installation Manual

Share
Download
Siemens RUGGEDCOM RS900F Installation Manual Download Page 20

Chapter 2

Installing the Device

RUGGEDCOM RS900F

Installation Guide

10

Mounting the Device on a DIN Rail

IMPORTANT!

Heat generated by the device is channeled outwards from the enclosure. As such, it is recommended

that 2.5 cm (1 in) of space be maintained on all open sides of the device to allow for some

convectional airflow.
Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient

temperature and improve the long-term reliability of all equipment mounted in the rack space.

NOTE

For detailed dimensions of the device with either DIN rail or panel hardware installed, refer to

Section 5.7, “Dimension Drawings”

.

CONTENTS

•

Section 2.4.1, “Mounting the Device on a DIN Rail”

•

Section 2.4.2, “Mounting the Device to a Panel”

Section 2.4.1

Mounting the Device on a DIN Rail

For DIN rail installations, the RS900F can be equipped with a DIN rail bracket pre-installed on the back of the

chassis. The bracket allows the device to be slid or clipped onto a standard 35 mm (1.4 in) DIN rail.
To mount the device to a DIN rail, do the following:
1. Align the slot in the bracket with the DIN rail.

Summary of Contents for RUGGEDCOM RS900F

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands