Siemens
Siemens
Siemens
Siemens
Siemens Industry
Industry
Industry
Industry
Industry,,,,, Inc.
Inc.
Inc.
Inc.
Inc.
Building
Building
Building
Building
Building T
TT
TTec
ec
ec
ec
echnologies Di
hnologies Di
hnologies Di
hnologies Di
hnologies Division
vision
vision
vision
vision
P/N 315-033420-13
INTRODUCTION
The Model RNI from Siemens Industry, Inc., allows for
the remote installation of the PMI/PMI-2/PMI-3, Global
PMI/PMI-2/PMI-3 (on XNET), SSD-C-REM (on HNET),
and the LVM/LCM-8/SCM-8/FCM-6/SIM-16/OCM-16
(on CAN) modules. When used in a REMBOX4, the
FMT and LVM are also supported.
The HNET/XNET can be wired either Style 4 or Style
7. The RNI must be placed in between two NIC-Cs
when used in a Style 7 Network with the Global PMI/
PMI-2/PMI-3 (on XNET) or the SSD-C-REM (HNET).
When using the PMI/PMI-2/PMI-3, the RNI may be
located in the middle or at the end of the HNET. Refer
to the table below for the allowable locations of
modules at the end of a HNET or XNET.
a
f
o
d
n
E
e
h
t
t
a
t
n
e
m
e
c
a
l
P
e
l
u
d
o
M
k
r
o
w
t
e
N
T
E
N
X
r
o
T
E
N
H
T
E
N
H
T
E
N
X
4
e
l
y
t
S
7
e
l
y
t
S
4
e
l
y
t
S
7
e
l
y
t
S
M
E
R
-
C
-
D
S
S
Y
N
*
*
3
-
I
M
P
/
2
-
I
M
P
/
I
M
P
)
T
E
N
H
(
Y
Y
*
*
-
I
M
P
/
I
M
P
L
A
B
O
L
G
)
T
E
N
X
(
3
-
I
M
P
/
2
*
*
Y
N
k
r
o
w
t
e
n
s
i
h
t
n
o
d
e
w
o
ll
a
t
o
N
*
,
d
e
w
o
ll
A
=
Y
,
d
e
w
o
ll
a
t
o
N
=
N
The CAN network may only be wired Style 4. The RNI may be located at the end or in
the middle of a CAN network. A 24VDC input is also required. This can be obtained
from the PSC-12 power limited output (TB3) or any 24 VDC UL/ULC regulated, power
limited power supply listed for fire protective signaling use. Audio signals for the LVM
and FMT are connected to TB1 of the PSC-12.
The RNI mounts in the rear of either the REMBOX2 or REMBOX4 enclosures. It can
also be installed in a CAB1, CAB2, or CAB3 using the mounting plate RNI-CAB-BRKT.
The RNI provides terminal blocks for all field wiring connections. Internal connections
are made to plug in connectors specifically provided for each of the installed modules.
The HNET/XNET and the CAN networks can be used simultaneously.
Remote Network Interface
Installation Instructions
Model RNI
X
H
24 V
TB1
1
2
9
10
P1
1
4
3
6
4
1
3
6
P3
P4
TB2
RNI
TB3
TB4
TB5
TB6
2
1
JP1
P6
S1
P5
P7
OFF
ON
1
2
7
8
P2
Figure 1
RNI Remote Network
Interface
