background image

2.  control output Y11 was energized for more than the “Minimum output on time”; 

(factory setting 1 minute, adjustable by parameter P15) 

Note: 

Control output Y12 delivers a control command which is inverted to the control 

 

command at output Y11 and which can be used for normally open valves. 

Heating / cooling  
mode 

With the RDF210, the changeover between cooling and heating takes place either 
automatically via a heating / cooling changeover sensor or a remote changeover 
switch. If the controller was set to ”Cooling only” or ”Heating only”

,

 changeover will not 

be possible (parameter P22, factory setting ”Cooling only”). 

With the RDF210.2, when pressing the heating / cooling changeover button  , the 
controller will change from heating to cooling, or vice versa. 

Minimum output  
on time / off time Y11 

The minimum output on time and off time of Y11 can be adjusted from 1…10 minutes 
via parameters P15 and P16. Factory setting is 1 minute. In this case, any readjustment 
of the setpoint or of heating / cooling mode changeover will be used immediately for 
computing the output status and output Y11 may not hold the minimum on / off time of 
1 minute. 
If parameter P15 or P16 is set to a level above 1 minute, the minimum on / off time of 
Y11 will be maintained as set, even if the setpoint or changeover mode has been read-
justed. 

Fan operation 

The fan operates either in automatic mode or at the selected speed when using manual 
mode. In automatic mode, the fan speed depends on the setpoint and the current room 
temperature. When the room temperature reaches the setpoint, the control valve will 
close and the fan switch off: Temperature-dependent fan control (see diagram below). 
The individual switching differentials of the fan speeds can be adjusted via control pa-
rameters P08 – P13. 
 

Heating mode 

 

Cooling mode

 

W

SDH

SDH

SDH2

SDH3

Valve

Fan

W

SDC

SDC3

SDC2

SDC

Valve

Fan

Y11

Y11

Temp

Temp

Temp

Temp

Q3

Q2

Q1

Q3

Q2

Q1

30

58D

03

 

 

If desired, fan control can be set to ”Temperature-independent”, which means that ven-
tilation is always on, even within the dead zone, using at least fan speed 1. This can be 
selected individually for Normal operation using parameter P21 and for Energy Saving 
mode using parameter P20 (also refer to “Avoiding damage due to moisture”). 

Ventilation  
always on 

 
In automatic mode, a dwelling time of 2 minutes (factory setting) is active. The fan 
maintains that speed for at least 2 minutes before it switches to the next speed. This 
dwelling time can be adjusted from 1…5 minutes using parameter P14. 

Dwelling time 

 

4/15 

Building Technologies 

Room Temperature Controllers 

N3058en 

HVAC Products 

 

10.01.2006 

Summary of Contents for RDF210
















Reviews: