manualshive.com logo in svg

Siemens POWERS RL 243 MP, Technical Instructions

Share
Download
Siemens POWERS RL 243 MP Technical Instructions Download Page 8

Technical Instructions 

RL 243 MP Multi-Purpose Relay 

Document Number 155-042P25 
September 10, 2018 

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as 
design improvements are introduced. POWERS is a registered trademark of Siemens Industry, Inc. Other product or company names mentioned 
herein may be the trademarks of their respective owners. © 2018 Siemens Industry, Inc. 

 

Siemens Industry, Inc. 

Building Technologies Division 
1000 Deerfield Parkway 
Buffalo Grove, IL 60089 
+ 1 847-215-1000 

Your feedback is important to us. If you have 
comments about this document, please send them 
to 

[email protected]

 

Document No. 155-042P25  

Printed in the USA 

Page 8 

 

 

Installation 

(See Installation 
Instructions 129-121 
for more information.) 

Multi-Purpose Relay with integrel bracket can be installed on panels, ducts, unit 
ventilators, or any other vertical or horizontal surface. Relay also can be panel mounted to 
facilitate manual adjustment. 

Technical Bulletin

 155-246 (TB 148) shows panel mounting 

arrangement. 

•

 

Slotted base accommodates screws or bolts for direct horizontal mounting within 
panel or on a flat wall surface. 

•

 

Integral bracket allows vertical mounting with panel or on a flat wall surface. 

Dimensions 

 

Figure 11

.  

Dimensions in Inches (Millimeters)

. 

 

Summary of Contents for POWERS RL 243 MP









Reviews:

No comments

Brands by name

Popular brands

Load more brands