background image

Milltronics WD600 
Operating Instructions, 09/2016, A5E38964753_A

B

 

27

 

Technical data 

8

8.1

 

Specifications 

Accuracy 

± 0.5% or better of totalization over 25 to 100% operating range 

Accuracy subject to: On factory approved installations the belt scale systems totalized weight will be 

within the specified accuracy when compared to a known weighed material test sample. The test 

rate must be within the specified range of the design capacity and held constant for the duration of 

the test. The minimum material test sample must be equivalent to a sample obtained at the test 

flow rate for three revolutions of the belt or at least ten minutes running time, whichever is greater.  

Load Cell 

construction 

nickel plated alloy steel or 17-4 PH (1.4568) 

stainless steel 

degree of protection 

IP66 rated (nickel plated) 

IP68 rated (stainless steel) 

excitation 

10 V DC nominal, 15 V DC maximum 

output 

2 mV/V excitation at rated load cell capacity 

non-linearity 

0.02% of rated output 

hysteresis 

0.02% of rated output 

non-repeatability 

0.01% of rated output 

capacity 

nickel plated maximum ranges: 10, 15, 20, 30, 50 

kg 

stainless steel maximum ranges: 6, 12, 30 kg 

overload 

150% of rated capacity 

ultimate 300% of rated capacity 

temperature 

–40 to +65 °C (– 40 to +150 °F) operating range

–10 to +40 °C (–15 to +105 °F) compensated

Belt width 

300 to 1200 mm (12 to 48") 
Refer to Outline dimensions (Page 29) 

Summary of Contents for Milltronics WD600



































Reviews: