Siemens M20 Terminal Technical Description Download Page 51

Page: 51 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

AT+IFC

Set TE-TA local data flow control

Test command

AT+IFC=?

Response

+IFC: (list of supported <dce_by_dte>s), (list of supported <dte_by_dce>s) OK

Parameter

see set command

Read command

AT+IFC?

Response

+IFC: <dce_by_dte>,<dte_by_dce> OK

Note:

This flow control is applied for data mode

Parameter

see set command

Set command

AT+IFC=[<dce_by
_dte>[,<dte_by_dc
e>]]

Response

This parameter setting determines the data flow control on the serial interface for data mode.

Parameter

<dce_by_dte> specifies the method which will be used by TE when data is received from TA

None

XON/XOFF, don’t pass characters on to data stack

line 133: ready for receiving

XON/XOFF, pass characters on to data stack

<dte_by_dce> specifies the method which will be used by TA when data is received from TE

None

XON/XOFF

line 106: clear to send (CTS)

Reference

V.25ter

Note

There are no pins for line 133 at AD6426. TTP applies line 105 (RTS) for this method.

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands