Siemens M20 Terminal Technical Description Download Page 29

Page: 29 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

Table 5-1

Standard Hayes AT commands

*) Note

: it is not necessary to subsequently download a stored configuration (see commands AT&Y and AT&W) since

the stored configuration is automatically downloaded each time the system is started up.

5.3.1

Detailed description

AT%D

Automatic dialling phone number in mem. "ME" index "1" with DTR

Page 46

AT+DR

V.42bis data compression reporting control

Page 47

AT+DS

V.42bis data compression control

Page 48

AT+GCAP

Request complete TA capabilities list

Page 48

AT+GMI

Request manufacturer identification

Page 49

AT+GMM

Request TA model identification

Page 49

AT+GMR

Request TA revision identification

Page 49

AT+GOI

Request global object identification

Page 50

AT+GSN

Request TA serial number identification

Page 50

AT+ICF

Set TE-TA control character framing

Page 50

AT+IFC

Set TE-TA local data flow control

Page 51

AT+ILRR

Set TE-TA local rate reporting mode

Page 52

AT+IPR

Set fixed local rate

Page 53

Repeat previous command line

Execute command

Response

Repeat previous command line

Note:

it does not have to end with terminating character.

Parameter

Reference

V.25ter

Note

(pause)+++(pause) ESC from data mode to command mode

Execute command

+++(pause)

Response

If TA receives pause(0,5sec) +++ pause (0,5sec), TA interrupts the data flow on the AT interface,
switches to command mode.

Notice: The command is available only in data mode.

Parameter

Reference

Hayes

Note

+++ is a Hayes command.

Command

Function

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands