Siemens LF98BC540B, Instructions For Installation And Use Manual

Page: 3 / 12

3
Toxic gases from the chimney or the extraction shaft are
sucked backed into the living space.
■
Adequate incoming air must therefore always be ensured.
■
An incoming/exhaust air wall box alone will not ensure
compliance with the limit.
Safe operation is possible only whenever the partial vacuum in
the place where the firing equipment is installed does not
exceed 4 Pa (0.04 mbar). This can be achieved whenever the
air needed for combustion is able to enter through openings
that cannot be sealed, for example in doors, windows,
incoming/exhaust air wall boxes or by other technical means.
In any case, consult your responsible chimney sweep. He is
able to assess the house's entire ventilation setup and will
suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the vapour extractor hood
is operated exclusively in the recirculation mode.
Risk of fire!
from flying sparks. Do not install appliance above a solid fuel
heater (e.g. wood or coal) unless a closed, non-removable
cover is available.
Caution!
Risk of damage from heat accumulation due to too narrow gap
between appliance and high-sided unit or wall. Only one side
of the appliance may be installed directly next to a high-sided
unit or a wall. Distance between the appliance and wall or high-
sided unit must be at least 50 mm.
The specified safety distances must be observed. Also observe
the specifications for your cooking appliance. If gas
and electric hobs are operated together, the largest specified
distance applies.
The width of the extractor hood must correspond at least
with the width of the hob.
For the installation observe the currently valid building
regulations and the regulations of the local electricity and gas
suppliers.
Risk of electric shock!
from damaged connection cable. Do not kink or pinch
connection cable during installation.
Risk of fire, risk of injury!
from damaged connection cable. A damaged connection cable
must be replaced by a qualified technician (electrician).
Risk of injury!
From sharp edges during installation. Always wear protective
gloves while installing the appliance.
Risk of injury!
from a falling appliance. All safety screws and safety caps must
be firmly fitted.
Using the appliance
Risk of burns!
from hot appliance when used with cooking appliances. Keep
children away and ensure appliance is used properly.
Risk of injury, risk of damage!
from objects falling on the appliance. Never place objects
on the appliance.
Risk of fire, risk of burns!
if gas hotplates not covered with cooking utensils. Always
use gas hotplates with appropriate cooking utensils. Regulate
flame to ensure that it does not lick over the cooking utensil.
Risk of burns, risk of damage!
if several gas hotplates are operated simultaneously. Never
operate two gas hotplates simultaneously on the highest flame
for longer than 15 minutes. The housing will become very hot
due to the intense heat.
Note: One large burner of more than 5 kW (Wok) is equivalent
to the power of two gas burners.
Risk of fire!
■
from grease deposits in the metal-mesh grease filter. Never
work under the appliance with a naked flame
(e.g. flambéing). Always operate appliance with metal-mesh
grease filter. Regularly clean the metal-mesh grease filter.
■
from overheated fats and oils. Heat fats and oils under
constant supervision only. Never extinguish fire with water,
always use a fire blanket, lid or plate.
Caution!
Risk of damage due to corrosion. Always switch on the
appliance while cooking to avoid condensation. Condensate
can produce corrosion damage.
Risk of injury!
due to LED lights of risk group 1. Do not look directly into the
switched on LED lights for longer than 100 seconds.
Cleaning and care
Risk of burns, risk of electric shock!
from appliance. Always leave appliance to cool down before
cleaning or servicing. Switch off fuse or pull out mains plug.
Caution!
■
Risk of damage due to ingress of humidity into the electronic
circuitry. Never clean operator controls with a wet cloth.
■
Surface damage due to incorrect cleaning. Clean stainless
steel surfaces in the grind direction only. Do not use any
stainless steel cleaners for operator controls.
■
Surface damage due to strong or abrasive cleaning agents.
Never use strong and abrasive cleaning agents.
Maintenance and repair
Risk of fire, risk of injury!
from improper repairs. Switch off fuse or pull out mains plug.
Repairs may be performed by a qualified technician
(electrician) only.
Risk of injury!
from defective or damaged appliance. Switch off fuse or pull
out mains plug and call customer service.
Risk of fire, risk of injury!
from damaged connection cable. A damaged connection cable
must be replaced by a qualified technician (electrician).
Risk of burns, risk of electric shock!
from defective bulbs. Switch off fuse or pull out mains plug.
Always replace defective bulbs immediately (leave bulbs
to cool down first) to prevent the remaining bulbs from
overloading.