Siemens LC97BCP50 Instructions For Installation And Use Manual Download Page 9

Cleaning and maintenance       

en

9

--------

Removing metal grease filter

1.

Open the lock and swing down the metal grease 

filter. When you do this, take hold of the metal 

grease filter from underneath with your other hand.

2.

Take the metal grease filter out of the holder.

Notes

– Fat may accumulate in the bottom of the metal 

grease filter.

– Hold the metal grease filter level to prevent fat 

from dripping out.

Cleaning the metal mesh grease filters

These instructions apply to several appliance variants. It 

is possible that individual features are described which 

do not apply to your appliance.

:

Warning – Risk of fire! 

Fatty deposits in the grease filter may catch fire. 

Regularly clean the grease filter. Never operate the 

appliance without a grease filter.

Notes

Do not use aggressive, acidic or alkaline cleaning 

products.

We recommend cleaning the grease filters every 2 

months.

When cleaning the metal grease filters, also clean 

the metal grease filter holder in the appliance using 

a damp cloth.

The metal grease filters can be cleaned in the 

dishwasher or by hand.

By hand:

Note: 

You can use a special degreaser to remove 

stubborn dirt. This can be ordered from the online shop.

Soak the metal grease filters in hot soapy water. 

Clean the filters with a brush and then rinse them 

thoroughly.

Leave the metal grease filters to drain on an 

absorbent material.

In the dishwasher:

Note: 

Slight discolouration may occur if the metal 

grease filters are cleaned in the dishwasher. This 

discolouration has no effect on the performance of the 

metal grease filters.

Use normal domestic dishwashing detergents. 

Do not clean heavily soiled metal grease filters 

together with cookware.

Place the metal grease filters in the dishwasher, 

leaving plenty of space around them. Do not trap the 

metal grease filters.

Select a temperature of no more than 70 °C.

Area

Cleaning products

Stainless steel

Hot soapy water: 

Clean with a dish cloth and then dry with a 

soft cloth.
Clean stainless steel surfaces in the direction 

of the grain only.
Special stainless steel cleaning products are 

available from our after-sales service or from 

specialist retailers.Apply a very thin layer of 

the cleaning product with a soft cloth.

Painted surfaces

Hot soapy water: 

Clean using a damp dish cloth and then dry 

with a soft cloth.
Do not use stainless steel cleaner.

Aluminium and plastic Hot soapy water: 

Clean with a soft cloth.

Glass

Glass cleaner: 

Clean with a soft cloth. Do not use a glass 

scraper.

Controls

Hot soapy water: 

Clean using a damp dish cloth and then dry 

with a soft cloth.
Risk of electric shock caused by penetrating 

moisture.
Risk of damage to the electronics caused by 

penetrating moisture. Never clean controls 

with a wet cloth.
Do not use stainless steel cleaner.

Summary of Contents for LC97BCP50





















Reviews: