Siemens HS636GD.1I, User Manual And Installation Instructions

Page: 26 / 48

en
Drying
26
If descaling is interrupted, you can no longer set any
operation. To ensure that the appliance is ready for op-
eration again, carry out two rinse cycles.
19.1 Preparing descaling
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
▶
Only use the liquid descaler recommended by us
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
▶
Remove descaling solution immediately with water.
1.
Mix the descaling solution:
‒
200 ml liquid descaler
‒
400 ml water
2. Open the control panel.
3.
Remove the water tank and pour the descaling solu-
tion into it.
4.
Once the descaling solution has been poured into
the water tank, slide the tank back in.
5.
Close the control panel.
19.2 Setting the descaling function
Requirement: → "Preparing descaling", Page 26
1. Press ​⁠.
2.
In the operating mode menu, select "Descaling".
a
The duration appears in the display. The duration
cannot be changed.
3. Press ​⁠ to start.
a
The descaling programme starts and the duration
counts down.
a
Once the first part of the descaling programme has
finished, an audible signal sounds. The appliance
prompts you to rinse twice.
4. To rinse the appliance, for each rinse cycle:
‒
Open the control panel and remove the water
tank.
‒
Thoroughly rinse the water tank and fill it with
fresh water.
‒
Slide in the water tank and close the control
panel.
‒
Use ​⁠ to start rinsing.
a
A signal sounds when each rinse cycle has ended.
5.
Once the second rinsing cycle is complete:
‒
Empty and dry the water tank.
→ "Emptying the water tank", Page 17
‒
Press ​⁠ to switch the appliance off
a
Descaling is complete and the appliance is ready
for use.
20 Drying
To prevent residual moisture, dry the cooking compart-
ment following operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
20.1 Drying the cooking compartment
You can dry the cooking compartment by hand or use
the drying function.
1. Allow the appliance to cool down.
2. Remove dirt from the cooking compartment.
3. Wipe away the water in the cooking compartment.
4. Dry the cooking compartment.
‒
Leave the appliance door open for one hour to
dry the cooking compartment by hand.
‒
In order to use the drying function, set the drying
function.
→ "Setting the drying process", Page 26
Setting the drying process
1. Allow the appliance to cool down.
2.
Remove coarse dirt from the cooking compartment
and wipe away moisture from the cooking compart-
ment floor.
3. Press ​⁠.
4.
In the operating mode menu, press the drying oper-
ating mode.
The duration is set to 10:00 min. and cannot be
changed.
5.
Press ​⁠ to start the drying function.
a
The appliance starts to dry and the duration counts
down.
6. Once the duration has elapsed:
‒
A message appears in the display.
‒
Press ​⁠ to silence the audible signal before
it is due to end.
‒
Press ​⁠ to switch the appliance off.