manualshive.com logo in svg

Siemens HC15, Getting Started Manual

Share
Download
Siemens HC15 Getting Started Manual Download Page 9

Getting Started with HC15 

Confidential / Preliminary 

s

 

HC15_startup_v01 

Page 9 of 31 

2007-01-22 

2.4 

Installing USB and Ethernet Drivers 

The HC15 driver package consists of three virtual devices, one by one automatically 
installed: 

•

  Siemens USB Com Port driver 

•

  Siemens Wireless Ethernet Adapter driver 

•

  Siemens HSDPA USB Modem driver 

During the installation, the HC15 USB interface will be assigned two virtual COM ports, one 
for the virtual modem port and one for the virtual application port. Windows will automatically 
allocate the next available COM port to each virtual interface. 
 
After plugging the USB cable Windows detects the HC15 as a new USB device. 
 

The 

Found New Hardware Wizard

 will 

start. Click 

Next

 to proceed with the 

installation of the “Siemens USB Com 
Port”. 
 
 
 
 
 
 
 
 
 
 
 
 

The progress of the driver installation is 
indicated.  
 
It is possible that there are up to 3 
warning messages saying that the 
drivers are not digitally signed. Please 
ignore the messages and press 

Continue 

anyway

. 

 

 
 
 
 
 
 
 
Click 

Finish

 to complete the installation 

of the “Siemens USB Com Port” 

Summary of Contents for HC15
































Reviews:

No comments

Brands by name

Popular brands

Load more brands