18
Replacing the cooking compartment bulb
Heat-resistant 25 W, 220/240 V bulbs, E14 bulb sockets and
the seals are available from the after-sales service. Please
specify the E number and FD number of your appliance.
:
Risk of burns!
Allow the cooking compartment and cooking compartment light
to cool before changing the bulb.
1.
Switch off the fuse in the fuse box or unplug at the mains.
2.
Turn the cover anti-clockwise to remove.
3.
Screw out the bulb by turning it anti-clockwise and replace
with a bulb of the same type.
4.
Slide the new seals and the clamping ring onto the glass
cover in the right order.
5.
Screw the glass cover with the seals back on again.
6.
Connect the appliance to the mains and reset the clock.
Never operate the appliance without the glass cover and seals.
The appliance is not in operation. A cook-
ing time is shown in the display
A control knob was unintentionally
pressed
Press and hold the
J
|
"
button
The
J
|
"
button was not pressed after
setting
Press the
J
|
"
button briefly to start the
cooking operation, or press and hold the
J
|
"
button to cancel the setting
0
and
‹
:
‹‹
light up in the display
Power cut
Reset the clock time (see section: Time-
setting options)
The
¯
indicator appears even though the
water tank is full
The water tank has not been inserted
properly
Slide in the water tank until it locks into
place.
The detection system is not working
Call the after-sales service
The
¯
indicator appears even though the
water tank is not yet empty, or the water
tank is empty but the
¯
indicator does not
appear
The water tank is dirty. The moving water
level indicators are jammed
Shake and clean the water tank. If the
parts cannot be released, obtain a new
water tank from the after-sales service
The water tank empties for no discernible
reason. The evaporator dish overflows
The water tank was not closed properly
Close the lid until you feel it lock into place
The tank lid seal is dirty
Clean the seal
The tank lid seal is defective
Obtain a new water tank from the after-
sales service
The evaporator dish has boiled empty
even though the water tank is full.
The water tank has not been inserted
properly
Slide in the water tank until it locks into
place
The feed line is blocked
Descale the appliance. Check whether the
water hardness range is set correctly
The
¯
indicator appears
The appliance has not been used for at
least 2 days and the water tank is full
Empty and clean the water tank. Always
empty the water tank after cooking
There is a "pop" noise during cooking
Cold/warm effect with frozen food, caused
by the steam
This is normal
When you cook with steam, a lot of steam
is created
The appliance is being automatically cali-
brated
This is normal
When cooking with steam, a lot of steam is
created again
The appliance is unable to calibrate itself
automatically if cooking times are too
short
Reset the appliance to the factory settings
(see Basic settings section). Then start
steaming at 100 °C for 20 minutes
Steam escapes from the ventilation slots
during cooking
This is normal
The appliance is not producing steam
properly
Limescale has formed in the appliance
Start the Descale programme (see section:
Descaling)
Error message
“‹‚‚
appears in the dis-
play
A button was pressed for too long or is
jammed
Press the
0
button to clear the fault mes-
sage. Press all of the buttons individually
and check if they are clean
An
“
... error message appears in the dis-
play
Technical fault
Press the
0
button to delete the error
message. Reset the clock if required. If the
error message appears again, call the
after-sales service
The appliance is no longer heating. The
colon flashes in the display
A button combination was pressed
Set the Steam operating mode to 35 °C,
then press and hold the
@
button until an
audible signal sounds. Press the
@
but-
ton again briefly
Problem
Possible cause
Notes/remedy
