Siemens Gigaset SX303isdn User Manual Download Page 143

Page: 143 / 183

140

Operation of entrance telephone

SX303/353isdn / englisch / A31008-X353-B100-2-7619 / door_intercom.fm / 14.11.2005

Operation of entrance telephone

Setting up the entrance telephone

You can select two door types for your entrance telephone:

◆

Door type 1:

for entrance telephones with door opening via ringing current (FTZ 123) – one

ringer button.

◆

Door type 2:

for entrance telephones with DTMF control – several programmable ringer buttons

(page 140).

The following internal number is provided for setting up an entrance

telephone:

Int.21

Setting up codes for »Door type 2 (DTMF)« entrance telephone

For entrance telephones controlled via DTMF codes, you can set up different codes.

Please refer to the corresponding information in the operating instructions for the

entrance telephone!
If you set up an internal user as door type 2, the codes are automatically activated using

presets.

Open the menu.

Set base

Select the menu item and confirm.

Settings

Select the menu item and confirm.

Enter system PIN if required (page 91).

Setup user

Select the menu item and confirm.

Setup device

Select the menu item and confirm.

INT21: Int.21

Select internal user and open

submenu.

Device type

Select the menu item and confirm.

either ...

Door type1

Select the menu item and confirm (

‰

= on).

or ...

Doortype2(DTMF)

Select the menu item and confirm (

‰

= on).

Open the menu.

Set base

Select the menu item and confirm.

Settings

Select the menu item and confirm.

Enter system PIN if required (page 91).

Setup user

Select the menu item and confirm.

Summary of Contents for Gigaset SX303isdn
























































































































































































Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands

Siemens Gigaset SX303isdn, User Manual

Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands