Siemens Gigaset S450 Owner'S Manual Download Page 45

Page: 45 / 58

Appendix

Gigaset S450 / English for Greece / A31008-M1716-T101-1-8U19 / appendix.fm / 07.09.2005

Appendix

Care

Wipe the base station and handset
with a

damp

cloth (do not use solvent)

or an antistatic cloth.

Never

use a dry cloth. This can cause

static.

Contact with liquid

If the handset has come into contact with
liquid:
1.

Switch the handset off and remove
the batteries immediately

2. Allow the liquid to drain from the

handset.

3. Pat all parts dry, then place the

handset with the battery compartment
open and the keypad facing down in a
dry, warm place for

at least 72 hours

(not in a microwave, oven etc.).

4. Do not switch on the handset again

until it is completely dry.

When it has fully dried out, you will
normally be able to use it again.

Questions and answers

If you have any queries about the use of
your telephone, you can contact us at any
time at www.siemens.com/
gigasetcustomercare . The table below
contains a list of common problems and
possible solutions.

The display is blank.

1. The handset is not switched on.

Press and

hold

the end call key

2. The batteries are flat.

Charge or replace the batteries
(page 7).

The handset does not respond to a key
press.

The keypad lock is activated.

Press and

hold

the hash key

(page 12).

"Base station x"

is flashing

in the display.

1. The handset is outside the range of the

base station.

Reduce the distance between handset/
base station.

2. The handset has been de-registered.

3. The base station is not switched on.

Check the base station mains adapter
(page 5).

Base Search is flashing in the display.

The handset is set for

Best Base

and no base

station is switched on or within range.

Reduce the distance between handset/
base station.

Check the base station mains adapter
(page 5).

Handset does not ring.

1. The ringtone is switched off.

Activate the ringtone (page 40).

2. Call diversion set to

All Calls

Switch off Call Diversion (page 15).

You cannot hear a ringtone/dialling tone.

Base station's phone cord has been replaced.

When purchasing a new cord, ensure that it
has the correct pin connections (page 6).

The other party cannot hear you.

You have pressed the

(INT) key. The

handset is "muted".

Switch on the microphone again (page 12).

The incoming call number is not displayed
although CLIP is set

Phone number identification is not enabled.

Caller

should ask network provider to

activate phone number identification (CLI).

Summary of Contents for Gigaset S450



























































Search results

Summary of Contents for Gigaset S450

Reviews:

Related manuals for Gigaset S450

Brands by name

Popular brands

Siemens Gigaset S450, Owner'S Manual

Search results

Summary of Contents for Gigaset S450

Reviews:

Related manuals for Gigaset S450

Brands by name

Popular brands