GAMMA wave
Technical Product Information
February 2007
Switch actuator wave GE 561/01
5WG3 561-4AB01
Siemens AG
wave GE 561/01, 6 pages
Technical Manual
Automation and Drives Group
Electrical Installation Technology
©
Siemens AG 2007
Update: http://www.siemens.de/gamma
P.O. Box 10 09 53, D-93009 Regensburg
Subject to change without prior notice
2.20.8.1/5
Programming the radio sensor to the corresponding
channel of the switch actuator is complete.
Note:
There is only a limited time available for connec-
tion, since the switch actuator wave exits the special
function after approx. 2 minutes.
If connection fails (e.g., if the distance between the
switch actuator and the radio sensor is too great), the
switch actuator wave exits the special function after
approx. 2 minutes without confirming success by rapid
flashing. The LED clears.
If further radio sensors are to be connected to the two
channels of the switch actuator wave, this operation
should be repeated.
Deleting a connection:
Deleting a connection is carried out by reassignment
(Diagram F).
To delete a connection between a radio sensor and a
channel of the switch actuator wave carry out the follow-
ing steps 1 and 2 one after the other:
1.
Activate the “special function channel A“ in the switch
actuator wave (brief actuation of the pushbutton for
(F2) no more than 3 seconds) or “special function
channel B” (long actuation of the pushbutton (F2) for
the duration of 3 to 6 seconds).
2
. Trigger the sending of the program telegrams at the
radio sensor to be programmed (see operating in-
structions for the corresponding device).
The connection of the radio sensor wave to the corre-
sponding channel of the switch actuator wave is thus de-
leted.
Deleting all the connections and resetting the switch
actuator wave to the supplied state:
Action: Very long actuation of the pushbutton (F2) for
at least 10 seconds.
Display: After 3 seconds the LED (F3) will flash once
briefly (approx. 0.1 sec.). After 10 seconds the
LED flashes rapidly for the duration of approx.
3 seconds with approx. 2.5 Hz (3 times per
sec.).
All connections to channels A and B of the switch actua-
tor are deleted. The device is in the supplied state.
If the pushbutton remains pushed for a maximum of 3
seconds or for 3 to 6 seconds after resetting to the sup-
plied state, it will be directly switched to the “special
function channel A” or “special function channel B“.
Time-switch operation (on-period 1 to 60 minutes):
The two channels of the switch actuator wave can be
operated respectively as a time switch. The connected
loads are thereby switched off automatically after a time
that can be set in steps of one minute. The on period
can be retriggered and is reset and restarted with each
receipt of an “ON” command via radio. With the receipt
of an “OFF” command it is switched off immediately.
The time-switch operation is activated or deactivated via
the “special function channel A” or the “special function
channel B”.
Activating the time-switch operation.
To activate the time-switch operation with an on-period
that can be set in steps of one minute in the range of 1
to 60 minutes, carry out the following steps 1A or 1B, 2,
3, and 4 one after the other:
1A. Switch on special function channel A.
Action: Brief actuation of pushbutton (F2) for the du-
ration of no more than 3 seconds.
Display: The LED (F3) begins to flash slowly within 3
seconds of the release of the pushbutton with
approx. 0.5 Hz (once in 2 seconds).
or
1B. Switch on special function channel B.
Action: Long actuation of the pushbutton (F2) for the
duration of 3 to 6 seconds.
Display: After 3 seconds the LED (F3) flashes briefly
once (approx. 0.5 sec.). Within 3 to 6 seconds
after the release of the pushbutton the LED
shows a steady light.
2. Select time-switch operating mode.
Action: Actuate the pushbutton (F2) again for the du-
ration of no more than 9 seconds.
Display: The LED (F3) clears after the actuation of the
pushbutton, and after the release of the
pushbutton within no more than 9 seconds
flashes quickly for the duration of approx. 3
seconds with approx. 2.5 Hz (3 times per
sec.).
3. Set on period in steps of 1 minute.
To set the on period in steps of one minute, actuate the
pushbutton (F2) again according to the desired on pe-
riod. Each actuation of the pushbutton extends the on
period by 1 minute (e.g., 1 pushbutton actuation = 1
minute on period, 5 actuations of the pushbutton = 5
minute on period, etc.).
