manualshive.com logo in svg

Siemens Flange Mount Kit, Mounting Instructions, Page: 7 / 28

Share
Download
Siemens Flange Mount Kit Mounting Instructions Download Page 7

DPD01156B

Siemens Industry, Inc.

7

Flange Mount Kit for Frame FS4

The kit consists of:

1. Top collar, (70CMR00281)

2. Bottom collar, (70CMR00280)

3. Side collars (2 pcs), (70CMR00282)

4. Internal fan, (70CPE00132, 70CPE00056) depends on the 

control unit

5. Sealing plug (3 pcs), (70CMR00324)

Additionally:

• 8 screws size 4x16 (for the top and bottom collar mounting)

• 3 screws size 4x12 (for the side collar mounting)

• 2 screws size 3.5x10 (for the bottom collar mounting)

FS4 Flange Mounting

If your drive is the Type 1/IP21-protected and there is the risk that dust or other impurities in the cooling air 
might end up inside the control unit, start the mounting with actions described in the steps 1 to 4.

If this is not needed, install the flange mounting kit proceeding directly to the step 5. Note, in this case the rear 
will not be according to the Type 12/IP54.

9266.emf

M3.5x10

M4x12

M4x16

5

2

1

3

3

4

Summary of Contents for Flange Mount Kit





























Reviews:

No comments