background image

Maintenance / Repair 

Faults 

  

101 

Building Technologies 

 

A6V10334410_h_en_-- 

Fire Safety 

 

2015-09-29 

8.11

 

Faults 

Faults are signaled on the front indicator. If there is any uncertainty, we 

recommend carrying out an LED and buzzer test. 
During the test, the following is checked: 

  Function test of the detector indicator 

  LED light test in three brightness levels 

  Sound of the buzzer at three different sound levels 

The test is activated with the 

 button and the result indicated with the 

LEDs. 

  The aspirating smoke detector is ready for use. 

  Press the button for 5 seconds. 

  The LED and buzzer test is carried out. The test is automatically 

undertaken in three stages. 

–  Stage 1: All the LEDs light up consecutively for one second at full 

brightness. The buzzer sounds loudly. 

–  Stage 2: All the LEDs light up consecutively for one second at reduced 

brightness. The buzzer sounds quieter. 

–  Stage 3: All the LEDs light up consecutively for one second at faint 

brightness. The buzzer sounds quietly. 

  The fault indicator 

 lights up briefly. If a fault is present, the 

corresponding LED indicator lights up at the same time for 3 seconds for Fault 

analysis [➙

 104

]

. 

  The indicators go out once the test has been completed successfully. 

  If a fault is present, the fault indicator flashes. 

  During normal operation, the three green LEDs light up. 

 

Normal operation, green LEDs light up 

 

Summary of Contents for FDA221



















































































































Reviews: