Siemens FCT010/DSL Operating Instructions Manual Download Page 110

Page: 110 / 180

Table 11-8

Ex conditions: Max. temperature vs. temperature classifaction (T amb: -20°C to +50°C)

DI 1/1.5/2.1/3

DI 6/15

100

135

180

11.3

Construction

Table 11-9

Designated use

Description

Specification

Measurement of process media

• Fluid Group 1 (suitable for dangerous fluids)
• Aggregate state: Paste/light slurry, liquid and gas

Table 11-10 Function and system design

Description

Specification

Measuring principle

Coriolis

System architecture

• Point-to-point (1 Modbus RTU master - 1 trans‐

mitter slave)

• Multidrop (1 Modbus RTU master - up to 32

transmitter slaves per segment. Max 247 slaves)

The MASS2100 and FC300 7ME4817-... is preconfigured for integration with the SITRANS
FCT070.

Note
NPT glands

When using NPT glands, user must take care when packing threads and installing cables that
sufficient tightness is obtained to prevent ingress of moisture.

Technical data
11.3 Construction

SITRANS MASS 2100 & FC300 (FCT010/DSL)

110

Operating Instructions, 06/2020, A5E39788682-AB

Summary of Contents for FCT010/DSL





















































































































































































Search results

Summary of Contents for FCT010/DSL

Reviews:

Siemens FCT010/DSL, Operating Instructions Manual, Page: 110 / 180

Search results

Summary of Contents for FCT010/DSL

Reviews: