Siemens FC300 Operating Instructions Manual Download Page 93

Page: 93 / 518

6.1.1

Warnings

CAUTION

Sensor and transmitter ordered separately
If the sensor and the transmitter are ordered separately, a "Set To Default" routine must be

performed. This can be done via SIMATIC PDM or via menu item 3.3.3 in HMI.

WARNING

Dangerous high voltage
Certain parts inside the device carry dangerous high voltage. The housing must be closed

and grounded before switching on the device.

WARNING

Improper handling
The sensor connected to this device can be operated with high pressure and corrosive media.

Therefore improper handling of the device can lead to serious injuries and/or considerable

material damage.

6.2

General requirements

Before commissioning it must be checked that:
● the device has been installed and connected in accordance with the guidelines provided in

Installing/Mounting (Page 37) and Connecting (Page 57)

● device installed in hazardous area meets the requirements described in Use in hazardous

areas (Page 20)

If the sensor and the transmitter are ordered separately, a "Set To Default" routine must be

performed. This can be done via SIMATIC PDM or via menu item 3.3.3 in HMI.

6.3

Local commissioning

6.3.1

Power-up

Power up the device. Devices with local display show a screen for initial startup.

6.3.2

Local display

The device is commissioned/operated with the touch keypad on the local display.

Commissioning

6.3 Local commissioning

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

Summary of Contents for FC300







































































































































































































































































































































































































































































































































Search results

Summary of Contents for FC300

Reviews:

Siemens FC300, Operating Instructions Manual, Page: 93 / 518

Search results

Summary of Contents for FC300

Reviews: