Siemens DI 16x24VDC HF Equipment Manual Download Page 19

Page: 19 / 46

Parameters

6.1

Module/channel parameters

Definition

Module/channel parameters are specific parameters whose configuration can affect the entire
module or channels.

Description

The following module/channel parameters are available:

Table 6-1

Parameters and their defaults

Parameter

Value range

Default

Parameter re‐

assignment in

RUN

Efficiency range

Diagnostics, Missing supply
voltage L+ (Page 20)

• Enabled
• Disabled

Enabled

Yes

Module

IO redundancy (Page 21)

• None
• 2 modules

None

Module

Diagnostics, Short-circuit to
ground (Page 21)

• Enabled
• Disabled

Enabled

Yes

Channel

Diagnostics, Wire break
(Page 21)

• Enabled
• Disabled

Enabled

Yes

Channel

Wire-break check (Page 21)

• Enabled
• Disabled

Enabled

Yes

Channel

Channel activated
(Page 22)

• Enabled
• Disabled

Enabled

Yes

Channel

Input delay (Page 22)

• None
• 0.05 ms
• 0.1 ms
• 0.4 ms
• 0.8 ms
• 1.6 ms
• 3.2 ms
• 12.8 ms
• 20 ms

3.2 ms

Yes

Channel

DI 16x24VDC HA
Equipment Manual, 10/2020, A5E39265608-AD

Summary of Contents for DI 16x24VDC HF















































Search results

Summary of Contents for DI 16x24VDC HF

Reviews:

Related manuals for DI 16x24VDC HF

Brands by name

Popular brands

Siemens DI 16x24VDC HF, Equipment Manual

Search results

Summary of Contents for DI 16x24VDC HF

Reviews:

Related manuals for DI 16x24VDC HF

Brands by name

Popular brands