manualshive.com logo in svg

Siemens DESIGO PX -U Series, Manual, Page: 6 / 12

Share
Download
Siemens DESIGO PX -U Series Manual Download Page 6

6/12 

Building Technologies 

PXC...-U – Automation stations   modular model 

CA1N9221en 

Building Automation 

 

23.09.2005 

Concerned 

LED 

Color 

Status 

Function 

Automation station 

RUN 

Green 

 

Red 

Continuously off 

Continuously on 

Continuously on 

No supply 

Supply OK, firmware OK 

RESET key pressed 

 STATUS 

Red 

Continuously 

off 

Continuously on 

 

Quick flashes 

Normal operation 

Hardware fault detected during self-test or 

automation station in "coma" operating state 

No validly licensed firmware 

 INFO 

Red 

 

Freely 

programmable 

 

 

 

 

 

Data traffic LON bus 

TX COM1  Yellow 

Flashing 

Data traffic on LON bus 

  

COM2 

Yellow 

 

Inactive 

 SERVICE 

 COM1 

 

 

 

 

Red Continuously 

off 

Flashing 

Flashing acc. to wink 

command pattern *) 

Continuously on 

LON node is configured 

LON node is not configured 

Physical identification of automation station 

after receiving wink command 

LON chip defect or service key was pressed 

again 

  

COM2 

Red 

 

Inactive 

 

 

 

 

 

Data traffic Ethernet / IP 

TX COM1  Yellow 

 

Inactive 

(PXA30-N..., PXA30-W...)   

COM2  Yellow 

Flashing 

Sends Ethernet data 

 SERVICE 

 COM1 

 

Red 

 

 

Inactive 

  

COM2 

Red 

Continuously 

off 

Flashing slowly 

Continuously on 

Ethernet OK 

IP address not configured 

No link pulse 

 

*) Wink command rhythm pattern: 

 

2s

1s

21s

5 Hz

5 Hz

00408

2s

1s

 

 

Mounting instructions 

The modular automation stations are particularly suitable for control panel front 
mounting as well as flush-panel and wall mounting. 
For control panel front mounting the device socket is held in place by clamps at all four 
corners (no tools required for mounting). The upper housing is fixed to the device 
socket with two screws. 
For flush panel mounting the plug-in terminal blocks can be repositioned whilst at the 
same time reversing the support bars to enable front access. The support bars absorb 
the screw force and also provide the means of fixing the device to the wall. 

Instead of the front cover a PXM... operator unit can be fitted on the modular auto-
mation station.  

For 

PXM20-E

 mounting (ethernet cable) see the mounting instructions delivered with 

the operator unit! 
 

•

 Insert 

the 

PXA30… extension module

 fully 

into its socket (

to a depth of 

1.5 mm), 

using slight force. 

Then 

check that the plug is safely snapped on

 to ensure safe 

and smooth functioning. 

•

 

Do not touch

 the connector pins (electrostatic discharge) 

Note 

STOP

 

Note! 

.
.
.
.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

.
.
.

Summary of Contents for DESIGO PX -U Series













Reviews:

No comments