Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 23

Page: 23 / 83

Installation

PXL Conventional Fire Alarm Control Panel

STEP 7Install the PCM-1

The installation kit for the PCM-1 consists of the following items:

ITEM

PART NUMBER

QUANTITY

plastic bezels

195-293693

power/cable

555-194066

3-position terminal block cover

305-192323

9-position terminal block cover

305-387037

PCM-1 LED label

575-493753

3.9K, 1/4W, EOL resistors

140-820186

zone labels

575-194072

4-position terminal block

150-094071

#6 x 3/8 Phillips screws

906-220606

If Class A conversion modules are to be used, refer to the

PZC-4D

Installation Instructions,

P/N 315-094164, before continuing with the

PCM-1 installation.

Mounting the PCM-1:

1. Place the PCM-1 board on the PMK-1 mounting bracket with the

component side facing down and with the locating pins protrud-

ing through the bottom of the bracket, as shown in Figure 11.

2. Fasten the PCM-1 to the mounting bracket at the positions

marked

in Figure 11 using the screws provided.

3. Remove the backing from the PCM-1 LED label and place it on

the PCM-1 bezel (Refer to Figure 11).

4. a. Complete the zone label for the zone overlay with the

appropriate zone description (Refer to Figure 12).

For example:

Floor 1, East Wing

Floor 1, West Wing

Slip the label under the overlay so the information shows

through.

b. Fill in the terminal block label with the appropriate zone

information.

5. Place each bezel in the appropriate position on the PCM-1 board

(Refer to Figure 11). Be sure that the locating pin on each bezel

goes through the appropriate hole in the bracket. Fasten the

bezels to the mounting bracket at the positions marked

Figure 11, using the screws provided.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands