Siemens Cerberus PRO FC721 Technical Manual Download Page 11

Page: 11 / 118

About this document

How displays are represented in the document

11 | 118

Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

Version

Edition date

Brief description

2010-07

Edition for MP3.0 XS
● Amendments to MP3.0
● Amendments to PMI & mainboard FCM2027
● Various minor changes
● Naming amended

2009-05

Technical manual FC721

1.5 How displays are represented in the document

With very few exceptions, the fire control panels and fire terminals are displayed in

this document in tables.
Deviations between the original and the table are indicated by means of examples

in the figures below:

Figure 1: Display with window and bar

Main menu
Exit with <C>

Access level 3

Message summary
Functions
Favorites
Topology

(1)
(2)
(3)
(4)

Element search
Event memory
Login/logout
Settings/administration

(5)
(6)
(7)
(8)

Function

On/Off

Function

All

LED

test

Table representation: Display without window

Selecting element category
Zone
Section
Area
Sounder
Physical channel

(1)
(2)
(3)
(4)
(5)

Table representation: 'Select element category' window without bar

The table representation has the following key deviations from the

original:

● Font and representation (not inverted)
● Windows are indicated separately without display background
● No bars to indicate the position and list length
● No frame around selection

Summary of Contents for Cerberus PRO FC721























































































































Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands

Siemens Cerberus PRO FC721, Technical Manual

Search results

Summary of Contents for Cerberus PRO FC721

Reviews:

Related manuals for Cerberus PRO FC721

Brands by name

Popular brands