manualshive.com logo in svg

Siemens 7ME652, Operating Instructions Manual, Page: 34 / 86

Share
Download
Siemens 7ME652 Operating Instructions Manual Download Page 34

Cable specifications     

● Only use cables with at least the same degree of protection as the sensor to install the 

sensor.

● The line length from the cable gland to the terminals must be kept as short as possible. Line 

loops in the terminal box must be avoided.

● To guarantee the IP67 degree of protection, use cables with the required specifications.

WARNING

Protective conductor terminal     
The required cable is min. AGW16 or 1.5 mm

2

  Cu.

WARNING

Wire insulation   
For field wiring installation: Ensure that the national requirements of the country in which 

the flowmeters are installed is met.

See also

Cable data (Page 53)

5.1

Remote installation

Note
Remote installation only
The following applies to remote installation of MAG 5000 / 6000 or MAG 6000 I.       

Connecting
5.1 Remote installation

SITRANS FM MAG 5100 W

34

Operating Instructions, 01/2020, A5E03063678-AC

Summary of Contents for 7ME652























































































Reviews:

No comments