Siemens 7ME305 Operating Instructions Manual Download Page 51

Page: 51 / 124

Functions

Operation is based on a hierarchically structured operating concept. All functions/parameters
are grouped logically and carry a menu number.

The seven main functions are selected in the main menu:

• Display (menu 1) (Page 51)

• Diagnostics (menu 2) (Page 53)

• Measuring functions (menu 3) (Page 54)

• Device outputs (menu 4) (Page 59)

• Identification (menu 5) (Page 63)

• Service (menu 6) (Page 64)

• Sensor parameters (menu 7) (Page 67)

The following section only describes how to manually operate the menus for the device settings.

7.1

Display (menu 1)

Language (menu 1.1.1)

Set display language (English, Deutsch, Francais, Español)

Line 1 (menu 1.1.2)

Set parameter value in line 1 (upper line on the display). Default is Flow.

Line 2 (menu 1.1.3)

Set parameter value in line 2 (lower line on the display). Default is Totalizer forward.

Display flow (menu 1.1.4)

Select the presentation of flow value (Physical Units (default), in % or Bar Diagramm (in %))

LCD lighting (menu 1.1.5)

Set the backlight turn-off. At power-off this function is automatically reset to the default value
Off.

Off: At infrared key operation, the light turns on automatically and off again 10 minutes after last
key action.

SITRANS FUS060 with PROFIBUS PA
Operating Instructions, 09/2021, A5E02225054-AD

Summary of Contents for 7ME305





























































































































Search results

Summary of Contents for 7ME305

Reviews:

Siemens 7ME305, Operating Instructions Manual, Page: 51 / 124

Search results

Summary of Contents for 7ME305

Reviews: