manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 23 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 23

Description of the device 

4.3 Components of the product 

SCALANCE W1788-x / W1748-1 
Operating Instructions, 03/2022, C79000-G8976-C484-05 

23

4.3

 

Components of the product 

The following components are supplied with the product: 
• A SCALANCE device with pre-installed bracket for securing to a DIN rail
• Two grounding screws
• One cover for PLUG slot
• Three protective caps for the M12 sockets

–

2 x Ethernet

–

1 x power supply

• Protective caps for the antenna sockets:

–

4 x for SCALANCE W1788-1 / W1748-1

–

8 x for SCALANCE W1788-2

Note 

The wall mounting set and the bracket set for securing the device to a standard rail are 

not included in the scope of delivery, see Accessories (Page 24). 

Please check that the consignment you have received is complete. If the consignment is 

incomplete, contact your supplier or your local Siemens office. 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments