Siemens 6ES7647-0BA00-0YA2 Operating Instructions Manual Download Page 68

Page: 68 / 71

SIMATIC IOT2050

Operating Instructions, 03/2020, A5E39456816-AA

Glossary

CE marking

Communauté Européene: The CE symbol confirms the conformity of the product with all

applicable EC directives such as the EMC Directive.

COM interface

The COM interface is a serial V.24 interface. The interface is suitable for asynchronous data

transfer.

Debian

Debian is a Linux distribution composed of free and open-source software. Debian systems

currently use the Linux kernel or the FreeBSD kernel. Linux is a piece of software started by

Linus Torvalds and supported by thousands of programmers worldwide. FreeBSD is an

operating system including a kernel and other software.

Distribution framework

Exemplary reference distribution "Debian" of Embedded Linux (see "Debian").

Drivers

Program parts of the operating system. They adapt user program data to the specific formats

required by I/O devices such as hard disk, printers, and monitors.

Embedded Linux

Linux for industrial, embedded systems (see "Debian").

ESD Guideline

Guideline for using electrostatic sensitive components.

Ethernet

Local network (bus structure) for text and data communication with a transfer rate of

100/1000 Mbps.

Summary of Contents for 6ES7647-0BA00-0YA2








































































Search results

Summary of Contents for 6ES7647-0BA00-0YA2

Reviews:

Related manuals for 6ES7647-0BA00-0YA2

Brands by name

Popular brands

Siemens 6ES7647-0BA00-0YA2, Operating Instructions Manual

Search results

Summary of Contents for 6ES7647-0BA00-0YA2

Reviews:

Related manuals for 6ES7647-0BA00-0YA2

Brands by name

Popular brands