Siemens 6ES7647-0BA00-0YA2 Operating Instructions Manual Download Page 62

Page: 62 / 71

Technical support

A.2 Troubleshooting

SIMATIC IOT2050

Operating Instructions, 03/2020, A5E39456816-AA

A.2

Troubleshooting

Error pattern

Possible cause

Possible remedy

Host monitor flashes black for a

few seconds when you insert

the DC connecting terminal to

the device.

You turned the switch on before

you connect the DC connecting

terminal.

Avoid turning on/off the device

by plugging /unplugging the DC

connecting terminal.
Use a external switch to control

the power of the device.

User button can't work when

Arduino shield reset pin is work-

ing.

User button and Arduino inter-

face reset pin can't work at

same time.

Avoid using user button and

Arduino interface reset pin at

the same time.

Summary of Contents for 6ES7647-0BA00-0YA2








































































Search results

Summary of Contents for 6ES7647-0BA00-0YA2

Reviews:

Related manuals for 6ES7647-0BA00-0YA2

Brands by name

Popular brands

Siemens 6ES7647-0BA00-0YA2, Operating Instructions Manual

Search results

Summary of Contents for 6ES7647-0BA00-0YA2

Reviews:

Related manuals for 6ES7647-0BA00-0YA2

Brands by name

Popular brands