Siemens 6ES7647-0BA00-0YA2 Operating Instructions Manual Download Page 22 | Manualshive

Page: 22 / 71

background image

Installing and connecting the device
3.2 Mounting the device

SIMATIC IOT2050

22

Operating Instructions, 03/2020, A5E39456816-AA

3.2.3

Wall mounting

3.2.3.1

Vertical wall mounting

The device is suitable for horizontal or vertical wall mounting.

Note
The device must be installed on the plate of an enclosure.

Requirement

●

Two mounting brackets

●

Two screws

●

T8 screwdriver

Procedure for mounting

1. Lay the mounting brackets on the rear of the device.
2. Fasten the brackets with supplied screws.
3. Mark the bore holes, drill the required holes in the wall and fasten the device to the wall

using two screws.

«
...
20
21
22
23
24
...
»

Summary of Contents for 6ES7647-0BA00-0YA2








































































Reviews:

No comments

Related manuals for 6ES7647-0BA00-0YA2

Brand: BAB TECHNOLOGIE Pages: 75

KoolKey EKA 200

Brand: Danfoss Pages: 2

Brand: Sangoma Pages: 4

Brand: IC nexus Pages: 36

Brand: D-Link Pages: 7

DPG-2000W - AirPlus G Wireless Presentation Gateway

Brand: D-Link Pages: 12

Brand: D-Link Pages: 37

DSA 5100 - Airspot - Gateway

Brand: D-Link Pages: 28

Brand: D-Link Pages: 12

Brand: D-Link Pages: 50

Brand: D-Link Pages: 67

Brand: D-Link Pages: 17

Brand: D-Link Pages: 13

Brand: D-Link Pages: 2

Brand: D-Link Pages: 37

Brand: D-Link Pages: 42

Brand: D-Link Pages: 83

Brand: D-Link Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands