Siemens 6ES7547-1JF00-0AB0 Manual Download Page 32

Page: 32 / 41

Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)

Manual, 03/2019, A5E45488510-AA

Technical specifications

Technical specifications of the IO-Link Master CM 8xIO-Link communication module

Article number

6ES7547-1JF00-0AB0

General information

Product type designation

CM 8xIO-Link

HW functional status

FS01

Firmware version

V1.0.0

•

FW update possible

Yes

Product function

•

I&M data

Yes; I&M0 to I&M3

Engineering with

•

STEP 7 TIA Portal configurable/integrated

as of version

V15.1 with HSP 274

•

STEP 7 configurable/integrated as of ver-

sion

Configurable via GSD file

•

PROFIBUS as of GSD version/GSD revi-

sion

GSD as of Revision 5

•

PROFINET as of GSD version/GSD revi-

sion

GSDML V2.34

Supply voltage

Rated value (DC)

24 V

permissible range, lower limit (DC)

20.4 V

permissible range, upper limit (DC)

28.8 V

Reverse polarity protection

Yes

Input current

Current consumption, max.

50 mA; without load

Encoder supply

Number of outputs

Output current

•

Rated value

1 A; 4 A total current per module

24 V encoder supply

•

Short-circuit protection

Yes; per channel, electronic

IO-Link

Number of ports

•

of which simultaneously controllable

IO-Link protocol 1.0

Yes

Summary of Contents for 6ES7547-1JF00-0AB0










































Search results

Summary of Contents for 6ES7547-1JF00-0AB0

Reviews:

Related manuals for 6ES7547-1JF00-0AB0

Brands by name

Popular brands

Siemens 6ES7547-1JF00-0AB0, Manual

Search results

Summary of Contents for 6ES7547-1JF00-0AB0

Reviews:

Related manuals for 6ES7547-1JF00-0AB0

Brands by name

Popular brands