manualshive.com logo in svg

Siemens 6ES7157-1AB00-0AB0, Manual

Share
Download
Siemens 6ES7157-1AB00-0AB0 Manual Download Page 12

Product overview 

 

2.3 Functions 

 

Interface module IM 157-1 PN (6ES7157-1AB00-0AB0) 

12

 

Manual, 12/2016, A5E32347036-AD 

Requirements 

The following table shows the software requirements for the use of PROFINET IO functions 

with the IM 157-1 PN interface module. 

Table 2- 1 

Software requirements for PROFINET IO functions 

PROFINET IO function 

Configuration software 

STEP 7 (TIA Portal) V13 or 

higher 

(with GSD file) 

STEP 7 V5.5 SP4 or higher 

(with GSD file)/Software from 

third-party manufacturer

2

 

Real-time communication 

X 

X 

Isochronous real-time commu-

nication 

X 

X 

Device replacement without 

programming device 

X 

X 

Media redundancy 

X 

X 

Shared device 

X

1

 

X 

 

1

  Use a S7-1500 CPU as a controller to use a shared device with STEP 7 (TIA Portal). 

2

  Systems of third-party manufacturers: Depending on the range of functions of the third-party sys-

tem 

Real-time communication 

A transmission method for PROFINET IO based on a cyclic data exchange with a provider-

consumer model. 

Isochronous real-time communication 

Synchronized transmission method for cyclic exchange of IRT data between PROFINET 

devices. A reserved bandwidth within the send clock is available for IRT data. The reserved 

bandwidth ensures that IRT data can be transferred at reserved synchronized intervals, 

without being influenced by other higher network loads (e.g., TCP/IP communication, or 

additional real-time communication). 
A topological configuration is required for IRT. 

 

 

Note 
IO controller as sync master with IRT communication 
We recommend that you also operate the IO controller as a sync master when configuring 

IRT communication. 
Otherwise IRT and RT configured IO devices may fail if the sync master fails. 

 

Summary of Contents for 6ES7157-1AB00-0AB0







































Reviews:

No comments

Brands by name

Popular brands

Load more brands