Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 30

Page: 30 / 264

Description, device design, dimension drawing

2.2 Connections and terminal designation

SITOP UPS1600 / BAT1600 / UPS1100

Equipment Manual, 07.2021, A5E37775406-11-76

2.2.1.4

PROFINET/Ethernet connection

Figure 2-10 PROFINET/Ethernet connection

The Ethernet interface

⑤

corresponds to the standard full duplex up to 100 Mbit/s electrical

(100BASE-TX) according to IEEE 802.3.
Properties of the Ethernet interface:
•

Transfer rate 10/100 Mbit/s

•

Two RJ45 sockets, i.e. integrated switch, for RJ45 connector

•

Cable type 100Base-TX (CAT5)

•

Autonegotiation

•

Auto-crossover communication via TCP/IP and PROFINET

The strain relief (see Section PROFINET/Ethernet connector (Page 189)) is implemented using

a Siemens IE FastConnect RJ45.
The physics of the Ethernet interface is implemented so that PROFINET IO according to

standards IEC 61158 and IEC 61784-2 is possible. For PROFINET, conformance class B must be

maintained as a minimum.
The Ethernet/PROFINET interface permits:
•

Configuration and monitoring using the SITOP Manager

•

Monitoring via the Web server

•

Integration and communication of the DC-UPS with other automation components from

Siemens and the open environment, e.g. IPC, PLC, HMI, OPC UA

•

Firmware update of the device via SITOP Manager, web server or STEP 7

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands