Siemens 6EP4131-0GB00-0AY0 Equipment Manual Download Page 172

Page: 172 / 264

Engineering and remote access

3.10 OPC UA server

SITOP UPS1600 / BAT1600 / UPS1100

172

Equipment Manual, 07.2021, A5E37775406-11-76

Display name

Data type

Definition

Description

HardwareBuffering

EnableClamp

Boolean

PropertyType

Enable buffering

HardwareEnable

ResetClamp

Boolean

PropertyType

When input voltage returns during buffering, the output is

switched off for a configurable time in order to reset con-

nected devices.

HardwareStartFrom

BatteryClamp

Boolean

PropertyType

Setting for 'Start from battery' on signal terminal

3.10.6.13

Identification

Display name

Data type

Definition

Description

IdentificationContact

Setpoint

String[64]

PropertyType

Contact

IdentificationDevice

NameSetpoint

String[32]

PropertyType

PROFINET device name

IdentificationLocation

Setpoint

String[44]

PropertyType

Location ID

Note

The various S7 systems interpret parameter "IdentificationLocationSetpoint" differently.
S7-1200 and S7-1500 correctly process the data sets.
S7-300, S7-400 and ET200SP do not fully support this data. Proceed as follows to correctly

save this data to these PLCs:
•

Write the data to identify the devices in the PLC code using function "WR_REC".

•

Read the data to identify the devices using the "RD_REC" functions.
For the ET200SP, a description of the two functions can be found here:

(

https://support.industry.siemens.com/cs/de/en/view/58649293

)

•

Alternatively, use the PRONETA

(

https://support.industry.siemens.com/cs/ww/de/view/67460624

) tool to read and write

data

3.10.6.14

Lock

Display name

Data type

Definition

Description

BreakLock

Method

ExitLock

Method

Lock for write access is withdrawn

InitLock

Method

Locks write access for other users

Locked

Boolean

PropertyType

Locked

LockingClient

String[16]

PropertyType

IP address of the blocking user

LockingUser

String

PropertyType

User that had locked

Summary of Contents for 6EP4131-0GB00-0AY0









































































































































































































































































Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands

Siemens 6EP4131-0GB00-0AY0, Equipment Manual

Search results

Summary of Contents for 6EP4131-0GB00-0AY0

Reviews:

Related manuals for 6EP4131-0GB00-0AY0

Brands by name

Popular brands