manualshive.com logo in svg

Siemens 6EP1437-3BA10, Manual, Page: 25 / 58

Share
Download
Siemens 6EP1437-3BA10 Manual Download Page 25

 

SITOP PSU8200 3ph 
Manual, 11.2014, C98130-A7638-A1-2-7629 

25

 

 

Installation 

5 

 

 

 

 

WARNING 

Hazard due to electric shock 
Before installation or maintenance work can begin, the system's main switch must be 

switched off and measures taken to prevent it being switched on again. If this instruction is 

not observed, touching live parts can result in death or serious injury. 

 

5.1

 

Line-side connection 

The SITOP PSU8200 3ph power supply is designed for connection to a 3-phase AC line 

supply with a rated voltage of 400-500 V AC, 50/60 Hz. 

 

Figure 5-1 

Line supply connection 

The line supply is connected using terminals L1, L2, L3 and PE (see Figure 5-1 Line supply 

connection (Page 25)), and must be implemented according to IEC 60364 and EN 50178 . 
A protective device (miniature circuit breaker or circuit breaker) and a disconnection unit for 

the power supply must be provided. A ground-fault circuit interrupter is not permissible 

against indirect contact as the only protective measure. This applies for the complete line 

supply protected by the ground-fault circuit interrupter. 

Summary of Contents for 6EP1437-3BA10



























































Reviews:

No comments