manualshive.com logo in svg

Siemens 3AD8, Instruction Manual

Share
Download
Siemens 3AD8 Instruction Manual Download Page 5

5

Designated usage

The RCU is used to connect the FS pole-
mounted or conductor-mounted circuit 
breaker into a utility SCADA system. Any 
other use is forbidden, unless the consent of 
Siemens has been obtained.

Changes to any part of the RCU or its accessories, 
that are carried out by the user or others, and not 
previously agreed by Siemens, will void the war-
ranty of the whole product.

Compatibility

This version of the RCU operating 
instructions is compatible with the following 
firmware and software versions:

Application

Applicable versions

RCU firmware

100

RCU Connect

V1.4.0.0

Table 1: Compatibility

 

Additional instructions

In addition to this manual, a protocol 
manual detailing the configuration options 
for each communications protocol is 
available. The utility may also be supplied 
with an RCU manual supplement which 
details the type of radio fitted, the radio 
cable and SCADA system protocol details 
which are specifically engineered for that 
utility (additional fees may be charged for 
this configuration service). Finally, if the 
RCU is fitted with a FS operator control 
panel (MLFB or order code 3AX1350-8C), 
the user will be supplied with a manual 
detailing the function and maintenance of 
the panel.

Summary of Contents for 3AD8









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands