SIEB & MEYER 0362151 Original Instructions Manual Download

Page: 25 / 26

Code

Description

Course of action

E.14.

Hilscher COM module: No "ready" signal after cold

boot

Check fieldbus connection.

Check the PLC software.

E.15.

Hilscher COM module: Data exchange not activated Check fieldbus connection.

Check the PLC software.

E.16.

Hilscher COM module: No communication with net-

work

Check fieldbus connection.

Check the PLC software.

E.17.

Hilscher COM module: Watchdog timeout

Check fieldbus connection.

Check the PLC software.

E.18.

Hilscher COM module: Communication error to net-

work

Check fieldbus connection.

Check the PLC software.

E.19.

Hilscher COM module: Module runs, but communi-

cation with internal dual-port memory cannot be es-

tablished.

Check fieldbus connection.

Check the PLC software.

Gateway 0362151 - PROFIBUS to SERVOLINK 4 Connection

Connectors, Switches and Displays

Summary of Contents for 0362151



























Search results

Summary of Contents for 0362151

Reviews:

Related manuals for 0362151

Brands by name

Popular brands

SIEB & MEYER 0362151, Original Instructions Manual

Search results

Summary of Contents for 0362151

Reviews:

Related manuals for 0362151

Brands by name

Popular brands