Sidewinder 6500 ESP Installation Manual Download

Page: 40 / 52

feature descriptions

The features of the system are described below. Features that have additional settings that can be selected only

when programming with the PC interface or Bitwriter are indicated by the following icon:

1-1 ACTIVE/PASSIVE ARMING:

When active arming is selected, the system will only arm when the transmitter

is used. When set to passive, the system will arm automatically 30 seconds after the last door is closed. To alert

the consumer of passive arming, the siren will chirp 20 seconds after the door is closed. This provides the con-

sumer with an audible warning prior to the system actually arming. At the 30 second mark, the system will arm,

but the siren will not chirp.

1-2 CHIRPS ON/OFF:

This feature controls the chirps that confirm the arming and disarming of the system.

1-3 IGNITION CONTROLLED DOOR LOCKS ON/OFF:

When turned on, the doors will lock three seconds after

the ignition is turned on and unlock when the ignition is turned off. The TechSoft Programmer or the 998T

Bitwriter™ will display separate steps for ignition lock and ignition unlock. They can be programmed on or off

independently.

menu #1 - basic features

FEATURE

ONE-CHIRP SETTING (DEFAULT)

TWO-CHIRP SETTING

3-1

Engine checking on

Engine checking OFF

3-2

Engine checking TACH

Engine checking VOLTAGE

3-3

Run time: 12 minutes*

Run time: 24 or 60 minutes*

3-4

Parking lights flashing

Parking lights constant

3-5

Crank time 0.6 seconds

0.8, 1.0, 1.2, 1.6, 1.8, 2.0, 4.0

3-6

Voltage check - high

Voltage check - low

3-7

Auxiliary output - factory disarm

Special accessory

3-8

Status output

Factory re-arm output

3-9

Anti-grind ON

Anti-grind OFF

menu #3 - remote start options

Summary of Contents for 6500 ESP





















































Search results

Summary of Contents for 6500 ESP

Reviews:

Related manuals for 6500 ESP

Brands by name

Popular brands

Sidewinder 6500 ESP, Installation Manual

Search results

Summary of Contents for 6500 ESP

Reviews:

Related manuals for 6500 ESP

Brands by name

Popular brands