8024844
QUICKSTART SICK LOCU1xx •Subject to change without notice • SICK AG • Waldkirch • Germany •
www.sick.com
TAGGABLE – LOCALIZATION LOC1xx | SICK
2
Figure 1. Tag dimensions in mm
*
dimension of tag with rechargeable battery
**
dimension only for tag with M8 connector (LOCU111-0x20)
***
left
LED only on rechargeable tags (charger LED)
All tags are delivered in inactive state to avoid battery draining
and activity during transport and storage.
Activation of LOCU101-0x00 tags is done by pulling out plastic
foil from the tag. The plastic foil must be pulled out slowly and
with care.
Figure 2. Direction of pulling out plastic foil
Activation of LOCU101-0x10/LOCU111-0x10 tags is done by
placing them on Qi compatible wireless charger.
Charging procedure
-
Place the tag on the Qi charger pad.
-
Charger should indicate charging status via LED within
a few seconds, the same should be indicated on the tag'
s charger LED.
-
Charging time is approximately 5,5 hours. (charging
current set to 73 mA)
-
After the charging is done, charger will indicate the
ready status via LED (depending on charger model; for
example: LED blinking or LED off)
-
Tags were tested with the following Qi chargers:
Samsung Fast Charge (EP-PN920), Samsung (EP-
PA510), Adata (CW0050).
Tags have to be fully charged before first use to avoid battery
damage.
Activation of LOCU111-0x20 tags is done by connecting them
to power supply (7-35V).
LOCU Tag
Models
Size (mm)
Weight
Power
supply
LOCU101-0x00
90.2 x 42.9 x 23.2
50 g
Coin Battery
CR2477,
1000mAh
LOCU101-0x10
LOCU111-0x10
90.2 x 42.9 x 17,5
45 g
Li-Pol 300
mAh,
wireless
charging
LOCU111-0020
90.5 x 42.9 x 23.2
43 g
External 7-
35 VDC
1
)
,
Power 1W
Operating
conditions
Indoor
−20°C … +60 °C
20 % … 85 % humidity without condensation
Warm-up time
Immediate
Sensors
LOCU101-0x00
LOCU101-0x10
3-axis accelerometer
LOCU111-0x10
LOCU111-0x20
3-axis accelerometer,
3-axis gyroscope,
3-axis magnetometer
Battery
management
Using accelerometer
Charging
2)
(Only LOCU1x1-0x10)
Charging Temperature: 0 ~ 45 °C
Charging Device: Only Qi compliant charger.
Charging Time / Current: 5.5 h / 73 mA
UWB
Channel 5, Band: 6240 MHz – 6748 MHz
Center Frequency: 6490 MHz
-41.3 dBm/MHz
WPAN
2400 MHz (SICK service interface only)
NFC
13.56 MHz
MTBF
Depending on environment in which the
devices are used, life expectancy is predicted
for 10+ years.
Pushbutton
LOCU101-0100, LOCU101-0110 and
LOCU111-0110
Enclosure
material
ABS (Acrylonitrile Butadiene Styrene)
1)
Connect max cable length of 30 meters (recommended) that are
grounded properly and never connect power cables with reverse
polarity
2)
Do not over-discharge the tag's battery, below 2.75V. Over-
discharging can damage the performance of the battery. To avoid over-
discharging by self-discharge, charge tags periodically.
1
DC
2
Not
connected
3
GND
4
Not
connected
Figure 3. Connection diagram for LOCU111-0x20 tags (view towards
the tag)
With a standard cable, e.g. SICK no 2094791, pin 1 (DC) corresponds
to brown color wire and pin 3 (GND) to blue color wire.
Turning the tag ON / activation
Technical data