manualshive.com logo in svg

SICK HIPERFACE DSL, Technical Information, Page: 25 / 172

Share
Download
SICK HIPERFACE DSL Technical Information Download Page 25

One edge on this pin triggers a position sampling. The polarity of the edge can be pro‐
grammed using the 

SPOL 

bit in the 

SYS_CTRL 

(00h) register. The protocol requires a

constant frequency of the signal at this pin, with deviations permitted within a set toler‐
ance band. Continuously, the protocol synchronizes the protocol frame with the signal
frequency at 

sync

.

NOTE

If the 

sync 

signal frequency is outside the tolerance range, re-synchronization of the

protocol is triggered. During the time that the re-synchronization is taking place, sam‐
pling is carried out with the former sync frequency until the re-synchronization is com‐
plete. For more details on the sync signal also see 

chapter 7.3.3

.

5.3.2

INTERRUPT signal

interrupt

 is a DSL Master digital output.

interrupt 

is set to "1" if an interrupt condition has been fulfilled in the DSL-Master.

The interrupt conditions are set using the registers 

MASK_H

, 

MASK_L 

and 

MASK_SUM

(see 

chapter 6.3.5

 and 

chapter 6.3.6

).

NOTE

During each write process in one of the registers 

EVENT_H 

or 

EVENT_L

, the 

interrupt

output is  masked  until the current SPI transaction has ended.

5.3.3

LINK signal

link

 is a DSL Master digital output.

link 

is effected by the content of the LINK bit in the 

MASTER_QM 

register (see

chapter 6.3.3

) and therefore indicates whether the DSL Master has produced a com‐

munications link to a connected HIPERFACE DSL

® 

motor feedback system.

link 

is intended to be a control signal for an LED display, but can also be used to con‐

trol the start-up performance (see 

chapter 7.1

) or for global error handling. 

link

 is reset if communication faults are detected.

5.3.4

FAST_POS_RDY signal

fast_pos_rdy

 is a DSL Master digital output.

fast_pos_rdy 

signals that a new fast position value is available and permits an

event-based reading of the position for incorporating latency reduction.

fast_pos_rdy 

is always available, even if the position value is invalid or no connec‐

tion to the encoder has been established.

Dependent upon the configuration in the register system control (see 

chapter 6.3.1

),

fast_pos_rdy 

displays either only the availability of positions based on user require‐

ments (edge at 

sync

 input) or all transmitted positions.

5.3.5

SYNC_LOCKED signal

sync_locked

 is a DSL Master digital output.

sync_locked 

indicates whether the 

sync 

signal  was correctly passed to the encoder,

or whether the IP Core is still in a synchronization phase. 

sync_locked 

drops to “0”

when the SYNC edge supplied by the application has been transported with more than
2 clock cycles of distortion.

INTERFACES 

5

8017595/ZTW6/2018-01-15 | SICK

T E C H N I C A L   I N F O R M A T I O N | HIPERFACE DSL

®

25

Subject to change without notice

Summary of Contents for HIPERFACE DSL













































































































































































Reviews:

No comments