manualshive.com logo in svg

SICK GM700 Ex, Operating Instructions Manual, Page: 57 / 102

Share
Download
SICK GM700 Ex Operating Instructions Manual Download Page 57

Checking status LEDs, error and warning messages

NOTE

Quick check of Measuring screens on the LC display of the evaluation unit:

b

Using the Operating Instructions, 

see "Operating and display elements (evaluation

unit)", page 58

.

When error or warning messages are present:

b

Determine and clear the error cause using the Operating Instructions, 

see "Serial

interface commands - Diag", page 65

, and the Error and Warning Message

Tables, 

see "Error messages", page 82

 and 

see "Warning messages", page 84

.

If the error cause cannot be cleared:

b

Contact SICK Service.

7.11.1

Operating states

Message on EvU display

Meaning

INIT

Initializing the evaluation unit

INITIALISATION

Initializing the SR-unit

SIGNAL_ADJUST

Adjusting amplification to changed transmission

MEASURING

Measuring operation

MEASURING LL

Measuring operation with active tracking of the laser
beam length (line locking)

MEASURING LD

Measuring operation; beam length tracked (line locking
done)

MAINTENANCE

Maintenance mode (no measurement)

DOWNLOAD

Download new software (for Service purposes only)

7.11.2

Select the ambient temperature range

NOTICE
Temperature stabilization: 30 minutes

The device stabilizes the temperature after the temperature is modified.

•

Warning message “DEV TEMP” is output during temperature stabilization.

1

Activate Parameter mode.

2

Menu path: Setting -> Ambient Temp.

3

Select the temperature range from the Table that matches the ambient conditions
best at the measuring location, 

see "Possible ambient temperatures", page 99

.

COMMISSIONING 

7

8019532/100Q/V1-1/2018-08 | SICK

O P E R A T I N G   I N S T R U C T I O N S | GM700 Ex

57

Subject to change without notice

Summary of Contents for GM700 Ex







































































































Reviews:

No comments